Smokeless I finally got my Apex today

[WGK]

Now if I can only get the barrel off. It says to remove the pivot pin, but which pin is it the small one or the large one. I messed with it for a few minuets and them had to come to work.

 

[Nhill]

Take the forearm off, then the pin (the one that it pivots on when you break open the barrel from the action) will slide out with a gentle tap from a blunt object.

 

[fullstream]

It's the big one. The apex was tougher to pull the pin on then I had figured it would be. Definately tougher then an encore.

 

[Roost 1]

It's the big one. The apex was tougher to pull the pin on then I had figured it would be. Definately tougher then an encore.

X2..... CVA uses oversized pins.. Actually I got one with a pin that was tooo big. It wouldn't go thru receiver...

 

[WGK]

I rapped on it pretty hard today and it did not budge. I get off work at 11:00 I will get it out tonight.

 

[WGK]

Thanks for the info fellows.

 

[Roost 1]

Best to find a wooden dowel about same size as pin to use to knock that hinge pin out.... This you won't damage anything.. Those pins can and will mushroom.

 

[fullstream]

I used a sockect that was just a lil smaller and put some duct tape on the end of it and pushed it through. Puttin it back in was a byotch. I couldn't imagine having multiple barrels and switching them out like an encore.

 

[WGK]

Interesting fullstream I was able to get the pin out but it was a little tough. I may have to try the socket when I put it back in. I was seriously thinking about a 35 Whelen barrel for this gun.

 

[Tenn.Guy]

Pins like that should be pressed in or out, not driven. A c-clamp could be modified to perform that task so as to make a switch barrel rifle more feasable. WGK, post the pin diameter and length along with a pic of the assembly, and I will look at making one for you.

I'm interested in seeing this. Getting the pin in and out is a nightmare. I would love to buy another barrel, but didn't see a benefit since you had to beat the old pin out.

 

[fullstream]

Pins like that should be pressed in or out, not driven. A c-clamp could be modified to perform that task so as to make a switch barrel rifle more feasable. WGK, post the pin diameter and length along with a pic of the assembly, and I will look at making one for you.

I'm interested in seeing this. Getting the pin in and out is a nightmare. I would love to buy another barrel, but didn't see a benefit since you had to beat the old pin out.

I am interested as well.

 

[Roost 1]

Whoever is interested Whitaker Guns has apex barrels with the fore arm.. $199!!!!
I think they have 35 Whelen and 5-6 other calibers as well...

 

[Tenn.Guy]

Whoever is interested Whitaker Guns has apex barrels with the fore arm.. $199!!!!
I think they have 35 Whelen and 5-6 other calibers as well...

Im interested if I can figure out an easy way to remove pin without affecting the scope from beating the pin!

 

[fullstream]

Whoever is interested Whitaker Guns has apex barrels with the fore arm.. $199!!!!
I think they have 35 Whelen and 5-6 other calibers as well...

Im interested if I can figure out an easy way to remove pin without affecting the scope from beating the pin!

Same here brother! Until there's an easier way to get it out that 45-70 barrel ain't never comin off!! If CR500 can figure this out I'd sure like to get a 7mm08.

 

[Tenn.Guy]

I'll get that for you if someone doesnt beat me to it!

 

[Tenn.Guy]

I did a little research and found the pin diameter is 10mm. Oversize pins are offered by other companies to tighten the joint up if it is loose. I still need a length on this pin. I don't own one of the guns so if someone could measure the pin length or for that matter, the reciever width at the pivot point and post it.

I fabricate my own specialty tools whenever possible. This is a simple tool

Per cheap caliper 31.92mm

 

[fullstream]

Much ablidged sir! Please let me know the cost. Look forward to being able to change the barrel out.

 

[Tenn.Guy]

Thanks very much. Would love to buy one.

 

[Roost 1]

Thanks very much. Would love to buy one.

X2 if possible.

 

[WGK]

Sorry I just now saw this. I too would be interested in purchasing one of these tools.

 

[WGK]

Roost 1 thanks much for the lead on the Apex barrels,, I ordered one today 224.00 shipped with a fore arm. That's a great deal. And guy a Whitaker guns said to spread the word they had several in different calibers.

 

[Roost 1]

Roost 1 thanks much for the lead on the Apex barrels,, I ordered one today 224.00 shipped with a fore arm. That's a great deal. And guy a Whitaker guns said to spread the word they had several in different calibers.

Welcome sir......

 

[redblood]

what is an apex. smokeless ml?

 

[Tenn.Guy]

what is an apex. smokeless ml?

Apex is CVA's version of the TC encore..... 45-70 rifle barrel converted = smokeless .45 mzl

 

[fullstream]

I got ahead of schedule and completed a prototype pivot pin removal/installation press this evening. Since WGK and I are in reasonably close proximity and he has a new barrel coming, he and I are making arrangements to try it out hopefully in the next week when his barrel comes in. We will update then.

Have y'all got a chance to try it out yet?

 

[Tenn.Guy]

I got ahead of schedule and completed a prototype pivot pin removal/installation press this evening. Since WGK and I are in reasonably close proximity and he has a new barrel coming, he and I are making arrangements to try it out hopefully in the next week when his barrel comes in. We will update then.

Have y'all got a chance to try it out yet?

Glad you asked, I have been dying to ask the past couple days, but hated to sound impatient

 

[WGK]

No we have not. Plan on getting together after season.

 

[Tenn.Guy]

Holidays, schedules, WGK got sick. I will go ahead and collect the needed materials for three more and will assemble after the trial run.

You are the man. Please let me know what I owe you. I really do appreciate this. (I am assuming I am in the 3 )

 

[fullstream]

Holidays, schedules, WGK got sick. I will go ahead and collect the needed materials for three more and will assemble after the trial run.

You are the man. Please let me know what I owe you. I really do appreciate this. (I am assuming I am in the 3 )

X2 on being the man! Sure hope I'm in the 3 as well

 

[Roost 1]

Holidays, schedules, WGK got sick. I will go ahead and collect the needed materials for three more and will assemble after the trial run.

You are the man. Please let me know what I owe you. I really do appreciate this. (I am assuming I am in the 3 )

X2 on being the man! Sure hope I'm in the 3 as well

X3 Hoping I am in there as well.....