- Location
- Tullahoma
This one hurts to post, but if I'm honest with myself, I've sat & stared at it for 2 years now. It's just too damn pretty for me to hunt with & I know I'm going to spend more time worrying about it getting scratched than I actually would hunting.
I built this up from parts. The action is a Sears model 52, which is the Sears specific brand Winchester Model 70. I had the entire action blueprinted & rebarreled to 6.5x55 Swede by E.R. Shaw. The barrel is 21", 5R rifled with a 1:8 twist. The profile was turned to match the factory M70 barrel which is basically a medium/light Sporter. The barreled action was then mirror polished & sent to a specialist refinisher in Wyoming for bluing. Along with that, the hinged bottom metal, bolt shroud, trigger, grip cap, scope mounts, sling swivels & all screws & fasteners were sent for color case hardening.
While all the metal was away for finishing, I found an unfinished, Exhibition grade walnut stock & set about hand fitting & finishing. I hand sanded everything to 800 grit & applied 24 coats of Alkanet oil, wet sanding the first 12. Once the color I wanted was achieved I applied 32 very fine coats of polymerized Tung oil (over a period of about 4 months) The stock was then sent to Ahlmans for hand cut checkering in a 22tpi Winchester point pattern. Once finished, the checkering was then very lightly oiled.
Once it was all back here & together, I added a Leupold FX-3 6x42 scope.
I've taken it to range 1 time to zero & work out a load & that's literally it. I don't think I've fired 40 shots since I finished it.
The whole project was a labor of love, because I wanted an Heirloom Quality gun, only to find out that I'm far better served with working guns. I don't know how many hours went into the build, but I'm pretty sure I clocked over 100 just in the stock.
Since then, it's literally sat in the cabinet slathered in anti-rust. I've occasionally taken it out to look at & fondle.
It's a crying shame to just have it sitting & it needs to go to someone who'll actually use & appreciate it for what it is, rather than just being a decoration.
I'm not gonna lie, I'm pricing this at slightly less than I have in it, but not much & the price is NOT negotiable. I paid nearly half the cost just for the stock alone.
$2000 will buy it & if it doesn't sell for that, it can stay in the cabinet.
Link to photo album.......
More photos available via text, on request.
Can meet around most places in middle Tn within an hour of Tullahoma.
I built this up from parts. The action is a Sears model 52, which is the Sears specific brand Winchester Model 70. I had the entire action blueprinted & rebarreled to 6.5x55 Swede by E.R. Shaw. The barrel is 21", 5R rifled with a 1:8 twist. The profile was turned to match the factory M70 barrel which is basically a medium/light Sporter. The barreled action was then mirror polished & sent to a specialist refinisher in Wyoming for bluing. Along with that, the hinged bottom metal, bolt shroud, trigger, grip cap, scope mounts, sling swivels & all screws & fasteners were sent for color case hardening.
While all the metal was away for finishing, I found an unfinished, Exhibition grade walnut stock & set about hand fitting & finishing. I hand sanded everything to 800 grit & applied 24 coats of Alkanet oil, wet sanding the first 12. Once the color I wanted was achieved I applied 32 very fine coats of polymerized Tung oil (over a period of about 4 months) The stock was then sent to Ahlmans for hand cut checkering in a 22tpi Winchester point pattern. Once finished, the checkering was then very lightly oiled.
Once it was all back here & together, I added a Leupold FX-3 6x42 scope.
I've taken it to range 1 time to zero & work out a load & that's literally it. I don't think I've fired 40 shots since I finished it.
The whole project was a labor of love, because I wanted an Heirloom Quality gun, only to find out that I'm far better served with working guns. I don't know how many hours went into the build, but I'm pretty sure I clocked over 100 just in the stock.
Since then, it's literally sat in the cabinet slathered in anti-rust. I've occasionally taken it out to look at & fondle.
It's a crying shame to just have it sitting & it needs to go to someone who'll actually use & appreciate it for what it is, rather than just being a decoration.
I'm not gonna lie, I'm pricing this at slightly less than I have in it, but not much & the price is NOT negotiable. I paid nearly half the cost just for the stock alone.
$2000 will buy it & if it doesn't sell for that, it can stay in the cabinet.
Link to photo album.......
More photos available via text, on request.
Can meet around most places in middle Tn within an hour of Tullahoma.
I usually have to buy breakfast when we meet up 
