Forums
New posts
Search forums
What's new
New posts
New Trophy's
New trophy room comments
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Classifieds
Trophy Room
New items
New comments
Latest content
Latest updates
Latest reviews
Author list
Series list
Search showcase
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Tennessee Gun Owners Forums
Muzzleloader
MZ Failure - take note
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="LanceS4803" data-source="post: 4938412" data-attributes="member: 9491"><p>I've had a Traditions Vortek for about 10 years. Used for mule deer, whitetails and occasional coyotes. Always the same basic load, 250 or 260 gr bullet and 110gr of BH209. This year stepped up to a 300gr for elk, same powder charge. (Leaving soon!)</p><p></p><p>Yesterday it quit working. Would impact the primer but primer did not fire, BUT the firing pin was stuck in the fired position. I could pop it back, but depressing the back of the firing pin would make it stick in the fired position. Inspection revealed the opening of the firing pin channel had narrowed (measured opening against end of channel), causing the firing pin the stick. </p><p></p><p>Got it home and discovered that the firing pin would not move freely in the channel. Contacted Traditions and was told I simply wasn't cleaning the rifle enough. They did not believe it was the firing pin opening size, that it was carbon build up and recommended various cleaners.</p><p></p><p>So, took an appropriate drill bit and hand turned off the constriction, .003 in diameter difference. Then used a flash hole deburring tool to remove any burr on either side of the channel. Smoothed out some raised areas on the actual firing pin and polished it up. Works slick as snot now. The receiver is aluminum but I still don't know why this happened.</p><p></p><p>Bottom line, this would have been disastrous if this had happened when lined up on an elk. Not sure how many use Traditions, or similar, but may be worth checking out.</p></blockquote><p></p>
[QUOTE="LanceS4803, post: 4938412, member: 9491"] I've had a Traditions Vortek for about 10 years. Used for mule deer, whitetails and occasional coyotes. Always the same basic load, 250 or 260 gr bullet and 110gr of BH209. This year stepped up to a 300gr for elk, same powder charge. (Leaving soon!) Yesterday it quit working. Would impact the primer but primer did not fire, BUT the firing pin was stuck in the fired position. I could pop it back, but depressing the back of the firing pin would make it stick in the fired position. Inspection revealed the opening of the firing pin channel had narrowed (measured opening against end of channel), causing the firing pin the stick. Got it home and discovered that the firing pin would not move freely in the channel. Contacted Traditions and was told I simply wasn't cleaning the rifle enough. They did not believe it was the firing pin opening size, that it was carbon build up and recommended various cleaners. So, took an appropriate drill bit and hand turned off the constriction, .003 in diameter difference. Then used a flash hole deburring tool to remove any burr on either side of the channel. Smoothed out some raised areas on the actual firing pin and polished it up. Works slick as snot now. The receiver is aluminum but I still don't know why this happened. Bottom line, this would have been disastrous if this had happened when lined up on an elk. Not sure how many use Traditions, or similar, but may be worth checking out. [/QUOTE]
Verification
Post reply
Forums
Tennessee Gun Owners Forums
Muzzleloader
MZ Failure - take note
Top