Tndeer Logo

Page all of 2 12>
Topic Options
#906998 - 09/09/08 07:49 PM Should broadheads be this picky?
Buckblaster
10 Point


Registered: 10/04/06
Posts: 3896
Loc: bradley county,TN/Lancaster,SC

Offline
Im shooting in the 290's and im 99.9% sure my bow is in perfe3ct tune. My question is My broadheads have to be turned to match my fletching. And they have to be perfect. I mean perfect. Within 1/16 of an inch perfect, its redicoulous. It took me forever to get 2 to shoot true. My arrows are spined correctly and I am shooting thunderhead 100's with 4" vanes with a good bit of offset.

Am I missing something?


Edited by Buckblaster (09/09/08 07:50 PM)
_________________________

Turn your caps lock of goober, we can hear you.

Top
#907004 - 09/09/08 07:51 PM Re: Should broadheads be this picky? [Re: Buckblaster]
MFBAB
10 Point


Registered: 01/08/08
Posts: 2990
Loc: Memphis, TN

Offline
I had to do that w/ Muzzy's on my bow, I switched to Montecs and no problem, I think they just create a little less drag.
_________________________
Missed it by that much....

Top
#907091 - 09/09/08 08:39 PM Re: Should broadheads be this picky? [Re: MFBAB]
Game Eye
14 Point


Registered: 08/06/00
Posts: 8394
Loc: Tennessee

Offline
Please explain what you mean to shoot true???
Top
#907550 - 09/10/08 08:22 AM Re: Should broadheads be this picky? [Re: Game Eye]
Radar
Non-Typical


Registered: 08/19/01
Posts: 31209
Loc: Kansas City, Mo.

Offline
Have you spin tested the broadheads on each arrow ? It is more important to spin test than line up fletchings to blades . What you are doing when you tighten thunderheads is seating them better in the insert . The rubber 0-ring can cause some variation in tightness .
Inserts that are not seated squarely to the shaft can cause broadheads to wobble .
Once you get speeds over 265 fps , high profile broadheads tend to wind plane more than low profile broadheads like Slick Tricks , etc .
_________________________

Top
#907560 - 09/10/08 08:32 AM Re: Should broadheads be this picky? [Re: Radar]
FLTENNHUNTER1
16 Point


Registered: 11/21/07
Posts: 16407
Loc: Tampa FL

Offline
I am shooting 29" 2413 XX78's with TH 100's at about 65-67 pounds. Not sure fps. I use a RazorTec. They shoot perfect to 40 yards. Anything 30 and under is too accurate; it shaves vanes.

Do what Radar says above.

I haven't paid any attention to matching my BH to vanes so I am sure they are not lined up and my setup shoots fairly well.
_________________________
"The fore horse of this frightful team is public debt. Taxation follow that, and in its turn wretchedness and oppression."
--Thomas Jefferson

17.9 Trillion http://www.usdebtclock.org/

Top
#908095 - 09/10/08 03:34 PM Re: Should broadheads be this picky? [Re: Game Eye]
Buckblaster
10 Point


Registered: 10/04/06
Posts: 3896
Loc: bradley county,TN/Lancaster,SC

Offline
 Originally Posted By: The Game
Please explain what you mean to shoot true???


true= straight/same as field point.
_________________________

Turn your caps lock of goober, we can hear you.

Top
#908098 - 09/10/08 03:37 PM Re: Should broadheads be this picky? [Re: Radar]
Buckblaster
10 Point


Registered: 10/04/06
Posts: 3896
Loc: bradley county,TN/Lancaster,SC

Offline
 Originally Posted By: Radar
Have you spin tested the broadheads on each arrow ? It is more important to spin test than line up fletchings to blades . What you are doing when you tighten thunderheads is seating them better in the insert . The rubber 0-ring can cause some variation in tightness .
Inserts that are not seated squarely to the shaft can cause broadheads to wobble .
Once you get speeds over 265 fps , high profile broadheads tend to wind plane more than low profile broadheads like Slick Tricks , etc .


No I havent. I can get them to have the same POI as my field points but its aggravating as snot. Once I have them just right they will hit just the same as my field point.
_________________________

Turn your caps lock of goober, we can hear you.

Top
#909210 - 09/11/08 08:32 AM Re: Should broadheads be this picky? [Re: Buckblaster]
Radar
Non-Typical


Registered: 08/19/01
Posts: 31209
Loc: Kansas City, Mo.

Offline
Spin test your broadheads on each arrow .
Go with Slick Tricks .
_________________________

Top
#909299 - 09/11/08 09:27 AM Re: Should broadheads be this picky? [Re: Radar]
BowGuy84
10 Point


Registered: 09/16/07
Posts: 4904
Loc: Nashville, TN and Louisville, ...

Offline
how do you spin test? roll on a flat surface and watch the tip? or use one of those spinner gizzmos that I think are a gimmick...when a table will do.

I square my shafts, line my blades up and my muzzys are spot on if my arrows (with field tips) are entering the trarget straight (tells me if my bow is in tune).

Top
#909618 - 09/11/08 12:21 PM Re: Should broadheads be this picky? [Re: BowGuy84]
Radar
Non-Typical


Registered: 08/19/01
Posts: 31209
Loc: Kansas City, Mo.

Offline
I have spin test rollers on my cut off saw . It is not a gimmick . ;\) I put a dot on a stationary object in front of the broadhead and spin it slowly while watching the point on the dot . If it wobbles , I discard that arrow for broadheads , and use it for field point practice .
A corner of a flat table works good too , but the spin tester is more accurate because the wobble can be seen easier .
One thing I do when I cut off my arrows is spin test them with a broadhead ferrule in the insert before the epoxy dries when gluing in the insert .
If it wobbles , I rotate the insert 1/4 turn . I keep doing this until it spins true . I also use a G5 squaring devise on the shaft ends after cutting them . It takes more time this way , but I get broadheads to spin true this way .
_________________________

Top
#913292 - 09/13/08 12:39 PM Re: Should broadheads be this picky? [Re: Radar]
paradis1142
10 Point


Registered: 11/25/04
Posts: 3852
Loc: crossville tn

Offline
Buy some rage heads.
_________________________
Once a Marine always a Marine

USMC...helping enemies of America die for their countries since 1775

Top
#913604 - 09/13/08 06:40 PM Re: Should broadheads be this picky? [Re: paradis1142]
Buckblaster
10 Point


Registered: 10/04/06
Posts: 3896
Loc: bradley county,TN/Lancaster,SC

Offline
 Originally Posted By: paradis1142
Buy some rage heads.


Give me $80 bucks so I can have six arrows decked with them \:D
_________________________

Turn your caps lock of goober, we can hear you.

Top
Page all of 2 12>


Moderator:  RUGER, Tennessee Todd, Tennessee Todd, Bobby G, Unicam, CBU93, stretch, Cuttin Caller, Kimber45, Mrs.Unicam, Crappie Luck 
Hop to:
Top Posters
4105874
RUGER
87595
Deer Assassin
65673
BSK
61389
Crappie Luck
51376
spitndrum
Newest Members
TnDear, buckslayer85, crose84, Fisher 1959, AKeys
13384 Registered Users
Who's Online
32 registered (2in1shot, bgrooms, Daniel n, BluegrassDan, Eric Kilby, gillis28, 6 invisible) and 121 anonymous users online.
Forum Stats
13384 Members
42 Forums
95877 Topics
1122695 Posts

Max Online: 788 @ 11/11/13 08:06 PM
Moon Phase
CURRENT MOON
October
Su M Tu W Th F Sa
1 2 3 4
5 6 7 8 9 10 11
12 13 14 15 16 17 18
19 20 21 22 23 24 25
26 27 28 29 30 31
Forum Donations
The TnDeer.Com Deer Talk Forum is for Tennessee Deer Hunters by Tennessee Deer Hunters. If you enjoy using our Talk Forum and would like to contribute to help in it's up-keep. Just submit your contribution by clicking on the DONATE button below and paying with PayPal or a major credit card. Any amount is much appreciated. Thanks for your support!

TN Burn Safe

Generated in 0.051 seconds in which 0.001 seconds were spent on a total of 14 queries. Zlib compression enabled.