Tndeer Logo

Page 1 of 2 12>
Topic Options
#829823 - 07/20/08 08:47 PM PVC feeder
jdyer
4 Point


Registered: 02/11/07
Posts: 176
Loc: Greene County, TN

Offline
I am looking to build a PVC feeder any suggestions or pics?
Top
#832791 - 07/22/08 03:09 PM Re: PVC feeder [Re: ]
SAWDUST
TnDeer Old Timer
8 Point


Registered: 11/25/99
Posts: 1013
Loc: cookeville tn.

Offline
two 5 gallon plastic buckets stacked on top of one another with the bottom cut out of the top one and a filler added to take up the space between the two makes a good cheap feeder. use the regular lid as a top. will hold about 40 -something pound of corn. cheap-cheap
_________________________
2 TIMOTHY 2:11 This is a faithful saying:
For if we died with HIM,
We shall also live with HIM.







Top
#833631 - 07/22/08 11:11 PM Re: PVC feeder [Re: SAWDUST]
12 Point
4 Point


Registered: 02/07/08
Posts: 277
Loc: Lake County Tenn

Offline
Another cheap way to make a great deer feeder is to get you a 10 foot section of 4 or 6 inch black sewer pipe with two caps. You can strap this to the side of a tree leaving about 10 inches of it turning out from the bottom of the tree. Put a cap on the bottom securing it good so animals can't paw it off, then cut you about a 4inch hole right above the cap, then fill it up with corn or your favorite type of deer food. Put the other cap on the top to keep rain out. Also be sure on the piece turned down on the ground to drill a small drain hole on the bottom side so it can drain out when it rains. I have been using feeders like this for several years now. Just remember to buy the solid black sewer pipe without holes. This also works great for salts and minerals that deer love so much. You can take a mineral block and crush it up some and feed it right down the tube also. Works great. Hope this has helps you with buiiding some cheap feeders. Can buy a whole 100 foot roll of black sewer pipe pretty reasonable, that will make roughly 12 to 14 feeders. Best of luck. Lake County Deer Hunter
Top
#834599 - 07/23/08 01:45 PM Re: PVC feeder [Re: 12 Point]
Coffee Break
6 Point


Registered: 06/04/08
Posts: 839
Loc: Shelbyville TN

Offline
I did mine a little different. I went up about 4"to 6" from bottom cap and cut half way threw then heat above cut with propane tourch and pushed it in to hold corn back. Push it almost all the way back and then i painted it gray and striped it black. I also drilled small holes in bottom cap to let any water out in a bad rain.

http://www3.sympatico.ca/konecny/deerfeeder.htm

Top
#836140 - 07/24/08 12:51 PM Re: PVC feeder [Re: Coffee Break]
Camp
12 Point


Registered: 11/30/07
Posts: 5917
Loc: Rutherford County / Mid TN

Offline
Just take a piece of 6"-10" diameter PVC, add a cap to one end (not glued on, so it can be removed) glue a 90 degree elbow piece on the other end and put a glued on cap on that. Cut a small hole in the cap to allow corn to flow out. Fill the length of the pipe with corn, place cap on completely open end, stand upright, with elbow and hole end down, bungee or rope pipe to a tree. With the pipe camo painted it blends perfectly with the tree, can not be knocked over and believe me a 10' or longer piece of pipe filled with corn can hold quite a bit.......

To determine what kind of volume and size you need.....
6" x 10' = 2 cubic feet = 90 lbs.
8" x 10' = 3.5 cubic feet = 158 lbs
10" x 10' = 5.5 cubic feet = 248 lbs

By Google measure search, standard shelled corn weighs 56 lbs per bushel or 45 lbs. per cubic ft. I'm sure that varies but that's where I got it.

These feeders last forever, can be made in a few minutes and wildlife can't knock 'em over, they hide well against the tree bark. Hope this helps.



Just strap it to a tree and you're done. To refill it easier....take it loose from the tree and you can angle the top end down to reach it better. Fill it up and re-bungee upright.

Top
#838141 - 07/25/08 05:44 PM Re: PVC feeder [Re: jdyer]
Marshal Dillon
TnDeer Old Timer
16 Point


Registered: 01/19/00
Posts: 10298
Loc: Dodge City/Gunsmoke

Offline
Go to the tndeer main menu http://www.tndeer.com/do-it-yourself.shtml plans for a PVC pipe feeder.
_________________________
"The government cannot give to anyone anything that it
does not first take from someone else."

Top
#838672 - 07/26/08 06:40 AM Re: PVC feeder [Re: Marshal Dillon]
jdyer
4 Point


Registered: 02/11/07
Posts: 176
Loc: Greene County, TN

Offline
Thanks guys I appreciate the input...looks like I have a new project
Top
#839240 - 07/26/08 07:11 PM Re: PVC feeder [Re: jdyer]
Boone 58
16 Point


Registered: 06/23/04
Posts: 14764
Loc: Food Plot

Offline
Awesome!
_________________________
The problem in America is not that ungodly people have said yes to ungodly things, but rather that Godly people have refused to say "no" to ungodly things.
Copied

Top
#847830 - 07/31/08 07:56 PM Re: PVC feeder [Re: Boone 58]
Jason Eldridge
10 Point


Registered: 05/31/04
Posts: 3422
Loc: South Carolina

Offline
ok, I read this thread and had to make one. I had some 4inch landscape/drain pipe. I figure anyone can find a piece for nothing. I spent 10 bucks at Home Depot for the rest. I bought a "y" connector ($6) and two end caps($2ea).


I measured 4 and 1/2 inches from the clean cut end of the pipe and cut it to give me a 4 and 1/2 inch piece of pipe for the "connector" from the "y" fitting to the end cap at the bottom(ground). I drilled many holes in the ground side end cap (holes smaller then corn).

Then with a small piece (about 4 inches) of pipe I cut it in half long ways, and put half of it inside of the (connector piece/end cap ground side) so that the corn wouldn't sit in the bottom and clog the drain holes or sit in possible water and let the water drain easier. I used the other half that I had cut long ways and screwed it to the bottom of the end cap(ground side) to keep the drain holes off the ground for good drainage. With the weight of the loaded feeder a small rock or piece of wood under it will keep the cut "spacer from ground" from hitting the ground.


It's very simple and untested, but I think it will work well. I plan on maybe having to trim some of the Y connector "feeding opening" for better access, but can't really check that until I fill it with corn. I have never "feed deer" and am not taking this into the woods. I built this for my fiance's back yard where she has seen one deer for the first time about a month ago in over 2 yrs. I hope to get some pics of it working \:\)



**NOTE** BTW, a PVC "Y" fitting (4inch) was $16 compared to $6 outside in the landscape plastic section \:\) like someone posted above. Also this pic was taken at my house, I dont plan to set it in a flower bed against a fence lol.
_________________________
The next best thing to being clever is being able to quote someone who is.

Top
#849411 - 08/01/08 07:51 PM Re: PVC feeder [Re: Jason Eldridge]
DOC1187
16 Point


Registered: 06/14/08
Posts: 11196
Loc: east tn

Offline
sweet
Top
Page 1 of 2 12>


Moderator:  gtk, Bobby G, Unicam, CBU93, stretch, Kimber45, Mrs.Unicam, Crappie Luck 
Hop to:
Top Posters
4105162
RUGER
86614
Deer Assassin
65010
BSK
60828
Crappie Luck
51376
spitndrum
Newest Members
bootsinsand, bigun714, clh200, tlwilliams, Forvols
13179 Registered Users
Who's Online
83 registered (TNRifleman, John3, scn, Master Chief, 7mmMag, prarie6288, 10 invisible) and 121 anonymous users online.
Forum Stats
13179 Members
42 Forums
90999 Topics
1063405 Posts

Max Online: 788 @ 11/11/13 08:06 PM
Moon Phase
CURRENT MOON
August
Su M Tu W Th F Sa
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Forum Donations
The TnDeer.Com Deer Talk Forum is for Tennessee Deer Hunters by Tennessee Deer Hunters. If you enjoy using our Talk Forum and would like to contribute to help in it's up-keep. Just submit your contribution by clicking on the DONATE button below and paying with PayPal or a major credit card. Any amount is much appreciated. Thanks for your support!

TN Burn Safe

Generated in 0.053 seconds in which 0.001 seconds were spent on a total of 15 queries. Zlib compression enabled.