Tndeer Logo

Page 1 of 1 1
Topic Options
#823087 - 07/15/08 07:26 PM Anyway to remove inserts?
Buckblaster
10 Point


Registered: 10/04/06
Posts: 3896
Loc: bradley county,TN/Lancaster,SC

Offline
???
_________________________

Turn your caps lock of goober, we can hear you.

Top
#823153 - 07/15/08 07:52 PM Re: Anyway to remove inserts? [Re: Buckblaster]
eddie c
Old School
12 Point


Registered: 08/09/01
Posts: 6389
Loc: jackson, tn

Offline
from what type of shaft?
here is how i remove from carbons. I heat up a field pt pretty hot then screw in the shaft, wait about a minute and twist. if it doesnt come out, I remove the nock and drop a drill bit inside the shaft and hammer it out by bouncing the bit up and down.
alum shafts I heat them up just enough to break the bond.

Top
#823389 - 07/15/08 10:19 PM Re: Anyway to remove inserts? [Re: eddie c]
Buckblaster
10 Point


Registered: 10/04/06
Posts: 3896
Loc: bradley county,TN/Lancaster,SC

Offline
Thanks, carbon shafts.
_________________________

Turn your caps lock of goober, we can hear you.

Top
#823493 - 07/15/08 11:36 PM Re: Anyway to remove inserts? [Re: Buckblaster]
Big J
16 Point


Registered: 03/10/06
Posts: 11992
Loc: Joelton

Offline
Put the field tip in then lighter it until hot. It will transfer the heat to the insert and you can twist the field tip with plyers like you are tightening it and the whole uinsert will turn then just remove
_________________________
Love God, Love people, Live Gospel!!

Top
#823667 - 07/16/08 06:54 AM Re: Anyway to remove inserts? [Re: Big J]
plinker22
16 Point


Registered: 02/07/05
Posts: 12858
Loc: Mountians of East Tennessee

content Online
I did not know this, very helpful info.
_________________________
NOTICE: The party in Hell has been canceled due to Fire!

Top
#823970 - 07/16/08 10:16 AM Re: Anyway to remove inserts? [Re: Big J]
CZ284
8 Point


Registered: 10/30/06
Posts: 1198
Loc: Rossville, Tn

Offline
 Originally Posted By: Big J
Put the field tip in then lighter it until hot. It will transfer the heat to the insert and you can twist the field tip with plyers like you are tightening it and the whole uinsert will turn then just remove


I do the same thing and still use hot melt glue to put the inserts in my broadhead / hunting arrows. For tuning, heat the broadhead (I use our gas stove on low burner setting) just enough to soften the glue, then turn the head and spin test them. On my practice arrows for field points, I use CA glue.

Top
#824074 - 07/16/08 12:08 PM Re: Anyway to remove inserts? [Re: eddie c]
Buckblaster
10 Point


Registered: 10/04/06
Posts: 3896
Loc: bradley county,TN/Lancaster,SC

Offline
 Originally Posted By: eddie c
from what type of shaft?
here is how i remove from carbons. I heat up a field pt pretty hot then screw in the shaft, wait about a minute and twist. if it doesnt come out, I remove the nock and drop a drill bit inside the shaft and hammer it out by bouncing the bit up and down.
alum shafts I heat them up just enough to break the bond.


I used superglue so that heating up stuff didnt work.

U took the knock out and stuck a big drill bit upside down in my shaft and swung it with one hand like a baseball bat and the insert came flying out and the dril bit did too, right acros the room \:D
_________________________

Turn your caps lock of goober, we can hear you.

Top
#824231 - 07/16/08 02:27 PM Re: Anyway to remove inserts? [Re: Buckblaster]
eddie c
Old School
12 Point


Registered: 08/09/01
Posts: 6389
Loc: jackson, tn

Offline
 Originally Posted By: Buckblaster
 Originally Posted By: eddie c
from what type of shaft?
here is how i remove from carbons. I heat up a field pt pretty hot then screw in the shaft, wait about a minute and twist. if it doesnt come out, I remove the nock and drop a drill bit inside the shaft and hammer it out by bouncing the bit up and down.
alum shafts I heat them up just enough to break the bond.


I used superglue so that heating up stuff didnt work.

U took the knock out and stuck a big drill bit upside down in my shaft and swung it with one hand like a baseball bat and the insert came flying out and the dril bit did too, right acros the room \:D


Top
#824348 - 07/16/08 03:47 PM Re: Anyway to remove inserts? [Re: eddie c]
Hillbilly Hunter
Killbilly
16 Point


Registered: 07/15/05
Posts: 18067
Loc: Branchville

Offline
good info
_________________________
...they never call me by my name, just Hillbilly...


Top
#825600 - 07/17/08 11:07 AM Re: Anyway to remove inserts? [Re: Hillbilly Hunter]
Viper (tp)
14 Point


Registered: 12/23/04
Posts: 9456
Loc: greenfield, tenn.

Offline
I have wondered this myself good info fellas! ;\)
_________________________
HUNTERS FOR THE HUNGRY, IT WORKS HERE IN WEAKLEY COUNTY!!

Top
Page 1 of 1 1


Moderator:  RUGER, Tennessee Todd, Tennessee Todd, Bobby G, Unicam, CBU93, stretch, Cuttin Caller, Kimber45, Mrs.Unicam, Crappie Luck 
Hop to:
Top Posters
4106437
RUGER
88232
Deer Assassin
65979
BSK
61899
Crappie Luck
51392
spitndrum
Newest Members
bcole0305, Browningbelgium7, cw308, TNDeerHunter270, rmyers@atpro1
13553 Registered Users
Who's Online
113 registered (baddnole, hard county, sgtwebb1, laserman, Brisco Darlin, Primos69, 12 invisible) and 188 anonymous users online.
Forum Stats
13553 Members
42 Forums
99398 Topics
1169261 Posts

Max Online: 788 @ 11/11/13 08:06 PM
Moon Phase
CURRENT MOON
November
Su M Tu W Th F Sa
1
2 3 4 5 6 7 8
9 10 11 12 13 14 15
16 17 18 19 20 21 22
23 24 25 26 27 28 29
30
Forum Donations
The TnDeer.Com Deer Talk Forum is for Tennessee Deer Hunters by Tennessee Deer Hunters. If you enjoy using our Talk Forum and would like to contribute to help in it's up-keep. Just submit your contribution by clicking on the DONATE button below and paying with PayPal or a major credit card. Any amount is much appreciated. Thanks for your support!

TN Burn Safe

Generated in 0.045 seconds in which 0.001 seconds were spent on a total of 14 queries. Zlib compression enabled.