Tndeer Logo

Page 1 of 1 1
Topic Options
#524419 - 12/11/07 07:30 AM New Win. 243 brass won't hold bullet
vonb
6 Point


Registered: 12/01/05
Posts: 816
Loc: TN

Offline
I have some brand new .243 Winchester brass that is brand new that was purchased 6-7 years ago. The other night, I went to load some rounds and ran into an issue. As always, my first step is to run them through a Forster F/L sizer (with expanding ball in place) using Imperial wax. I mainly do this to round out the case mouth.

After performing the step above, I went to charge and seat and the seating was where I ran into an issue. I was seating 100gr Remington Core-Lokts and after seating, I noticed that the case mouth was too large to reliably hold the bullet in place. Therefore, just shaking the case would move the bullet. Where have I gone wrong here?

I have performed these same steps many times in the past and no changes have been made to my die. This setup has worked well using 85gr HPBTs and 87gr VMAX. I'm using a Forster Co-Ax press.

Top
#524464 - 12/11/07 08:06 AM Re: New Win. 243 brass won't hold bullet [Re: vonb]
Whelen Man
TnDeer Old Timer
8 Point


Registered: 03/12/99
Posts: 2327
Loc: Athens, TN, USA

Offline
Good question. If you've got a caliper check the diameter of the 100 gr. Remingtons compared to the other bullets you've loaded in the past. Then check the outside diameter of the neck compared to loads from the past. That should tell something as to whether it's the brass or the bullet. Something is weird here. The only thing that has changed is the bullet. With the expander in place the brass shouldn't be the problem with new brass unless something happened to it during storage to harden it where it won't size properly.
_________________________
Recipient of the Coveted Senior Discount!

Top
#525361 - 12/11/07 07:50 PM Re: New Win. 243 brass won't hold bullet [Re: Whelen Man]
Sniper
TnDeer Old Timer
12 Point


Registered: 03/09/99
Posts: 5672
Loc: East TN

Offline
I had some Winchester .308 brass that was like this, it would not hold a .308 bullet with any neck tension at all. I could easily push the bullet into the case with my fingers. I resized it all to 7mm-08 and it worked fine for that caliber.
_________________________
David Tenney
US Market Representative
Trophy Game Safaris - Southern Africa
Tino and Amanda Erasmus
http://www.tgsafari.co.za
contact@tgsafari.co.za

Top
Page 1 of 1 1


Moderator:  RUGER, Bobby G, Unicam, CBU93, stretch, TurkeyBurd, Kimber45, Mrs.Unicam, Crappie Luck, gtk 
Hop to:
Top Posters
4106599
RUGER
88400
Deer Assassin
65979
BSK
62020
Crappie Luck
51392
spitndrum
Newest Members
yarddawg54, schiesser, bigdoc, Bggamehunter, willy2763
13605 Registered Users
Who's Online
3 registered (Daniel Willoughby, CAW, TX300mag) and 65 anonymous users online.
Forum Stats
13605 Members
43 Forums
100233 Topics
1180122 Posts

Max Online: 788 @ 11/11/13 08:06 PM
Moon Phase
CURRENT MOON
December
Su M Tu W Th F Sa
1 2 3 4 5 6
7 8 9 10 11 12 13
14 15 16 17 18 19 20
21 22 23 24 25 26 27
28 29 30 31
Forum Donations
The TnDeer.Com Deer Talk Forum is for Tennessee Deer Hunters by Tennessee Deer Hunters. If you enjoy using our Talk Forum and would like to contribute to help in it's up-keep. Just submit your contribution by clicking on the DONATE button below and paying with PayPal or a major credit card. Any amount is much appreciated. Thanks for your support!

TN Burn Safe

Generated in 0.005 seconds in which 0.001 seconds were spent on a total of 14 queries. Zlib compression enabled.