Tndeer Logo

Page 2 of 2 <12
Topic Options
#448780 - 10/15/07 09:32 AM Re: HELP: Scope removal question [Re: BigAl]
6 Point

Registered: 11/01/06
Posts: 668
Loc: Bartlett

Put some heat to it Al. Heat will cause the loc-tite to turn to liquid and you should be able to move it then. Cig lighter or a propane torch, just don't try to discolor the metal.
You sure you can skin Griz pilgrim?
Skin this one and I'll bring you another!

#448982 - 10/15/07 11:29 AM Re: HELP: Scope removal question [Re: Tnyoteboy]
8 Point

Registered: 11/09/04
Posts: 1156
Loc: Westmoreland

I knew of one guy who used Gorilla Glue. What a mess.
"The ability to go long periods without food and water, to control emotions and to kill 'calmly and deliberately' without remorse are the main qualifications of a good sniper."

#449110 - 10/15/07 12:30 PM Re: HELP: Scope removal question [Re: comprifleshooter]
RUGER Administrator
Bambi Killa

Registered: 11/19/99
Posts: 4106600
Loc: TN

Easiest way is to drill it out.
Use a bit just a little bit bigger than the threaded portion of the screw.
When you drill down just far enough the head will pop off.
Then you can remove the rings then you will have a little bit of the screw sticking up to get ahold of with some pliers and get it out.
If that don't work, you will have to heat it up as has been said.
Youth is wasted on the young.

#449213 - 10/15/07 01:39 PM Re: HELP: Scope removal question [Re: RUGER]
Whelen Man
TnDeer Old Timer
8 Point

Registered: 03/12/99
Posts: 2327
Loc: Athens, TN, USA

Sometimes screws like that will loosen up if you will use an appropriate sized torx head and tap it several times on the head before trying to loosen it up. It breaks the seal a little and many times only a few taps will make a world of difference. Then try the heat. It would be a whole lot cheaper to buy an appropriate torx head you can hammer on and if that don't work try a little heat also. You could try a flat ended punch of the correct size and go that route also. Some of the high carbon torx heads will shatter if you try this so buy a good one for loosening it up and a cheapie one for hammering on.
Recipient of the Coveted Senior Discount!

#450790 - 10/16/07 05:22 AM Re: HELP: Scope removal question [Re: Whelen Man]
Cull Buck Hunter
8 Point

Registered: 12/16/05
Posts: 1933
Loc: Cleveland,TN

Make sure that you have a clearance on both sides of the rings after they are tightened down. I have ran into a few that were metal to metal, that makes it hard to remove the rings. Drill it out, and take your time and do it right.

Buy US made products, your job may be next!

Page 2 of 2 <12

Moderator:  RUGER, Bobby G, Unicam, CBU93, stretch, TurkeyBurd, Kimber45, Mrs.Unicam, Crappie Luck, gtk 
Hop to:
Top Posters
Deer Assassin
Crappie Luck
Newest Members
yarddawg54, schiesser, bigdoc, Bggamehunter, willy2763
13605 Registered Users
Who's Online
0 registered and 30 anonymous users online.
Forum Stats
13605 Members
43 Forums
100241 Topics
1180147 Posts

Max Online: 788 @ 11/11/13 08:06 PM
Moon Phase
Su M Tu W Th F Sa
1 2 3 4 5
6 7 8 9 10 11 12
13 14 15 16 17 18 19
20 21 22 23 24 25 26
27 28 29 30 31
Forum Donations
The TnDeer.Com Deer Talk Forum is for Tennessee Deer Hunters by Tennessee Deer Hunters. If you enjoy using our Talk Forum and would like to contribute to help in it's up-keep. Just submit your contribution by clicking on the DONATE button below and paying with PayPal or a major credit card. Any amount is much appreciated. Thanks for your support!

TN Burn Safe

Generated in 0.005 seconds in which 0.002 seconds were spent on a total of 15 queries. Zlib compression enabled.