Tndeer Logo

Page 1 of 1 1
Topic Options
#397195 - 09/14/07 11:24 AM if tacks had 12" heads...............

Registered: 10/17/06
Posts: 40
Loc: Johnson City

I would have a tack driver.My 45cal optima is spraying 195 & 233g powerbelts all over at 50 yds.i am using 100g trip 7 pellets and trip 7 going back to the range tomorrow with 200g shockwaves to see if they will pattern and have some pyrodex to try.i also have 209 primers to try.
I have put around 25 rounds through this gun,is there any reason to think it is not broken in yet? I dont have alot of experience with smokepoles. Any suggestions will be appreciated.

#397246 - 09/14/07 11:59 AM Re: if tacks had 12" heads............... [Re: ]
8 Point

Registered: 06/02/05
Posts: 1638
Loc: Lake City, Tn

Get ya some valve gringing compound,take a oversized patch and put some on the patch and give it about 25 stokes,make sure that you go the full length of the barrel. Do this with about 8 differant patches. This will take out any burrs that are left over from the machining of the berrel. Next get someloose T-7 3f powder. Start out with 70 grains of powder and get your gun grouping good. Once you get the groups where you want,start increasing your powder in 5 grain increments, when your groups start to open up go back to the previous powder load. the lapping of the barrel takes some time but is well worth it. Also when shooting for accuracy swab between every shot.
Don't go pushin me against my will, I don't wanna have to fight ya, But I dern sure will,If ya don't want trouble you better just pass me on by.

Im a blackpowder junkie.

#397250 - 09/14/07 12:02 PM Re: if tacks had 12" heads............... [Re: ]

Registered: 10/17/06
Posts: 40
Loc: Johnson City

Yes,sparkling clean
#397266 - 09/14/07 12:12 PM Re: if tacks had 12" heads............... [Re: ethunter]
12 Point

Registered: 01/29/07
Posts: 6265
Loc: Adirondack Mtns, NY

Scoped?, steady rest?, you said clean, now or then? if then did it group at all with the first few shots?

I would clean it, start out with 75-80 gr. of powder, and increase as mentioned above.

I know this is an obvious, but is everything tight on the gun? stock, sights, etc. If using a rest, are you setting the stock on it or the barrel?


edited to add:

After the first two or three shots the barrel will be warm to hot, this will effect the remaining results. I have a tendency to shot one bullet, clean the gun reload and shot a second round, clean the gun shot a third round, to ge a true first shot result. Think about it how often do you shot two or three shots then aim at the animal......................? It is always the first shot out of the gun that day, most of the time.

Edited by FULLDRAWXX75 (09/14/07 12:18 PM)
“Two things are infinite: the universe and human stupidity; and I'm not sure about the universe.”
― Albert Einstein

#397383 - 09/14/07 01:08 PM Re: if tacks had 12" heads............... [Re: FULLDRAWXX75]
12 Point

Registered: 11/06/02
Posts: 7406
Loc: savannah, tn., usa

Most muzzleloader problems I have encountered have been either bad scopes or mounts. That is where I would start. If that is not the problem start backing down the powder in 5 grain increments until you get a good group. If velocity is too low when you get groups try another bullet.
Let em go and let em grow!
There is a difference in a turkey killer and a turkey hunter!

#402246 - 09/17/07 01:20 PM Re: if tacks had 12" heads............... [Re: muddyboots]
16 Point

Registered: 01/13/03
Posts: 10574
Loc: Warren Co

My first CVA loved the powerbelts. Heck it loved all the bullets I shot through it.

My new Winchester Apex (made by CVA) doesnt shoot powerbelts very well. THey are a bit too loose in the barrel. Now a 300gr xtp in the black sabot is another matter!

Try a different bullet, one with a sabot and see if you can get it to group.
If you can't trust people with freedom, how can you trust them with power ?

#402430 - 09/17/07 03:51 PM Re: if tacks had 12" heads............... [Re: ]
10 Point

Registered: 10/25/05
Posts: 3263
Loc: southwest iowa

The first scope I had on my encore gave me problems. New scope but it wouldn't stay zeroed after shooting several times. Also make a pencil mark on your ram rod so you know if your getting the bullet seated the same each time. I had that problem with loose powder and powerbelts, but I've been using the pellets ever since with no problems.
#405563 - 09/19/07 08:29 AM Re: if tacks had 12" heads............... [Re: ]

Registered: 10/17/06
Posts: 40
Loc: Johnson City

I am going to the range tonite and taking the scope off.If it still wont pattern with cva's recommended load(150g trip 7 and 195g powerbelts)they want the gun back. thanks to eveyone for suggestions
Page 1 of 1 1

Moderator:  RUGER, Tennessee Todd, Bobby G, Unicam, CBU93, stretch, Kimber45, Mrs.Unicam, Crappie Luck, gtk 
Hop to:
Top Posters
Deer Assassin
Crappie Luck
Newest Members
yarddawg54, schiesser, bigdoc, Bggamehunter, willy2763
13605 Registered Users
Who's Online
0 registered and 9 anonymous users online.
Forum Stats
13605 Members
43 Forums
100243 Topics
1180151 Posts

Max Online: 788 @ 11/11/13 08:06 PM
Moon Phase
Su M Tu W Th F Sa
1 2 3 4
5 6 7 8 9 10 11
12 13 14 15 16 17 18
19 20 21 22 23 24 25
26 27 28
Forum Donations
The TnDeer.Com Deer Talk Forum is for Tennessee Deer Hunters by Tennessee Deer Hunters. If you enjoy using our Talk Forum and would like to contribute to help in it's up-keep. Just submit your contribution by clicking on the DONATE button below and paying with PayPal or a major credit card. Any amount is much appreciated. Thanks for your support!

TN Burn Safe

Generated in 0.009 seconds in which 0.004 seconds were spent on a total of 14 queries. Zlib compression enabled.