Tndeer Logo

Page 1 of 2 12>
Topic Options
#3310854 - 08/03/13 05:17 PM I need a new archery guy
Master Chief
10 Point


Registered: 10/11/11
Posts: 3075
Loc: Henderson County

Offline
I can see my HIDDEN inserts. Anyone in the archery business should know what a H.I.T insert is and how to apply them. Can they be taken out?


These are Easton ST Axis FMJ N-Fused arrows.. just the cheapos
_________________________
Shed hunting and trail camera addict

"It's not whatcha got, it's what you give." -Tesla

"In every walk with nature one receives far more than he seeks."
-John Muir

Top
#3311116 - 08/03/13 09:46 PM Re: I need a new archery guy [Re: Master Chief]
UTGrad
16 Point


Registered: 12/01/07
Posts: 10229
Loc: Franklin, TN

Offline
Wah wah wah (cartoon trumpet sound)

Edited by UTGrad (08/03/13 09:47 PM)

Top
#3311127 - 08/03/13 10:14 PM Re: I need a new archery guy [Re: UTGrad]
Master Chief
10 Point


Registered: 10/11/11
Posts: 3075
Loc: Henderson County

Offline
Anyone ever try to remove a HIT insert with Easton epoxy? From what I read on the net you can't.
_________________________
Shed hunting and trail camera addict

"It's not whatcha got, it's what you give." -Tesla

"In every walk with nature one receives far more than he seeks."
-John Muir

Top
#3311136 - 08/03/13 10:27 PM Re: I need a new archery guy [Re: Master Chief]
deerhunter10
10 Point


Registered: 08/21/12
Posts: 3542
Loc: maury county tn

Offline
call matt eddie energy wave bowstrings. he should know or tndeerguy should know.

Edited by deerhunter10 (08/03/13 10:28 PM)
_________________________
GO VOLS






Top
#3311175 - 08/04/13 12:15 AM Re: I need a new archery guy [Re: deerhunter10]
TNDeerGuy
12 Point


Registered: 11/28/06
Posts: 6170
Loc: Old Hickory/Mt.Juliet, TN

Offline
They can be taken out, but it can be a pain and sometimes it is inevitable that you may damage the shaft beyond repair. If a shop did this, I would take it back to them before you run the risk of damaging a $10 arrow.

However, here are things that I know you can try, listed in order of not damaging the shaft.

1. Take nock out and put a drill bit in the shaft and "swing" the shaft letting the drill bit punch the insert out. Be careful though because sometimes when the insert comes out, the drill bit will be flying out with it.

2. Heat a pot of water to just about boiling and place the point end of shaft, with field point screwed in, in the water for about 10-15 minutes. Take shaft out and with a pair of pliers start working the point/insert outóit may take several times.

These next ones are a complete gamble and run a very high risk of damaging the shaft.

3. Take a drill bit and drill out the insert inside the shaftóbe very careful not to contact the shaft.

4. This will almost always get the insert out, but at least 50% of the time will damage the shaft! Screw field point into the insert and with a propane torch heat the end of the point slowly for 10-15 seconds, the heat will transfer down to the aluminum insert and will heat/loosen the epoxy. After 10-15 seconds, take pliers to the point and try to work insert outórepeat process until the insert breaks free. **Caution** Carbon does not like a lot of heat, really doesn't like any, so even if you get the insert out carefully inspect the end of the shaft for small hairline cracks.

There maybe other ideas out there, but these have worked for me over the years.

Top
#3311180 - 08/04/13 12:34 AM Re: I need a new archery guy [Re: TNDeerGuy]
Master Chief
10 Point


Registered: 10/11/11
Posts: 3075
Loc: Henderson County

Offline
 Originally Posted By: TNDeerGuy
They can be taken out, but it can be a pain and sometimes it is inevitable that you may damage the shaft beyond repair. If a shop did this, I would take it back to them before you run the risk of damaging a $10 arrow.

However, here are things that I know you can try, listed in order of not damaging the shaft.

1. Take nock out and put a drill bit in the shaft and "swing" the shaft letting the drill bit punch the insert out. Be careful though because sometimes when the insert comes out, the drill bit will be flying out with it.

2. Heat a pot of water to just about boiling and place the point end of shaft, with field point screwed in, in the water for about 10-15 minutes. Take shaft out and with a pair of pliers start working the point/insert outóit may take several times.

These next ones are a complete gamble and run a very high risk of damaging the shaft.

3. Take a drill bit and drill out the insert inside the shaftóbe very careful not to contact the shaft.

4. This will almost always get the insert out, but at least 50% of the time will damage the shaft! Screw field point into the insert and with a propane torch heat the end of the point slowly for 10-15 seconds, the heat will transfer down to the aluminum insert and will heat/loosen the epoxy. After 10-15 seconds, take pliers to the point and try to work insert outórepeat process until the insert breaks free. **Caution** Carbon does not like a lot of heat, really doesn't like any, so even if you get the insert out carefully inspect the end of the shaft for small hairline cracks.

There maybe other ideas out there, but these have worked for me over the years.


I will take them back and see what they can do. They dont carry the axis arrows but he will be ordering a set if he even slightly damages them
_________________________
Shed hunting and trail camera addict

"It's not whatcha got, it's what you give." -Tesla

"In every walk with nature one receives far more than he seeks."
-John Muir

Top
#3311181 - 08/04/13 12:35 AM Re: I need a new archery guy [Re: Master Chief]
Master Chief
10 Point


Registered: 10/11/11
Posts: 3075
Loc: Henderson County

Offline
Happy bday btw and thanks for the help
_________________________
Shed hunting and trail camera addict

"It's not whatcha got, it's what you give." -Tesla

"In every walk with nature one receives far more than he seeks."
-John Muir

Top
#3311281 - 08/04/13 08:34 AM Re: I need a new archery guy [Re: Master Chief]
ImThere
10 Point


Registered: 08/24/06
Posts: 3180
Loc: Lewisburg, Tn

Offline
 Originally Posted By: Master Chief
 Originally Posted By: TNDeerGuy
They can be taken out, but it can be a pain and sometimes it is inevitable that you may damage the shaft beyond repair. If a shop did this, I would take it back to them before you run the risk of damaging a $10 arrow.

However, here are things that I know you can try, listed in order of not damaging the shaft.

1. Take nock out and put a drill bit in the shaft and "swing" the shaft letting the drill bit punch the insert out. Be careful though because sometimes when the insert comes out, the drill bit will be flying out with it.

2. Heat a pot of water to just about boiling and place the point end of shaft, with field point screwed in, in the water for about 10-15 minutes. Take shaft out and with a pair of pliers start working the point/insert outóit may take several times.

These next ones are a complete gamble and run a very high risk of damaging the shaft.

3. Take a drill bit and drill out the insert inside the shaftóbe very careful not to contact the shaft.

4. This will almost always get the insert out, but at least 50% of the time will damage the shaft! Screw field point into the insert and with a propane torch heat the end of the point slowly for 10-15 seconds, the heat will transfer down to the aluminum insert and will heat/loosen the epoxy. After 10-15 seconds, take pliers to the point and try to work insert outórepeat process until the insert breaks free. **Caution** Carbon does not like a lot of heat, really doesn't like any, so even if you get the insert out carefully inspect the end of the shaft for small hairline cracks.

There maybe other ideas out there, but these have worked for me over the years.


I will take them back and see what they can do. They dont carry the axis arrows but he will be ordering a set if he even slightly damages them

He already damaged them imo. He needs to make it right
_________________________
Prancerciser!
Team Run 'N Gunners

Top
#3311296 - 08/04/13 08:51 AM Re: I need a new archery guy [Re: ImThere]
hoyt30
4 Point


Registered: 09/19/11
Posts: 160
Loc: east middle tn

Offline
I shoot the axis st with h i t. If the arrows were mine they would be replacing them. Be very careful with that carbon. I was changing broadheads the other day and heard a small pop, that shaft went to the trash. Carbon is very dangerous when broke.
Top
#3311395 - 08/04/13 10:46 AM Re: I need a new archery guy [Re: hoyt30]
fasteddie
4 Point


Registered: 09/27/09
Posts: 147
Loc: Nashville, TN

Offline
wow. wow. yeah id be taking it back and asking for another dozen
_________________________
Owner/Operator of Energy Wave Bowstrings, LLC. and Energy Wave Archery, Middle Tennessee's Newest archery pro shop and Elite Archery Dealer

Top
Page 1 of 2 12>


Moderator:  RUGER, Tennessee Todd, Tennessee Todd, Bobby G, Unicam, CBU93, stretch, Cuttin Caller, Kimber45, Mrs.Unicam, Crappie Luck, gtk 
Hop to:
Top Posters
4106599
RUGER
88400
Deer Assassin
65979
BSK
62020
Crappie Luck
51392
spitndrum
Newest Members
yarddawg54, schiesser, bigdoc, Bggamehunter, willy2763
13605 Registered Users
Who's Online
7 registered (rtaylor, TiminTN, duckriver, RAFI, Tenn.Guy, stuball1) and 73 anonymous users online.
Forum Stats
13605 Members
43 Forums
100233 Topics
1180121 Posts

Max Online: 788 @ 11/11/13 08:06 PM
Moon Phase
CURRENT MOON
December
Su M Tu W Th F Sa
1 2 3 4 5 6
7 8 9 10 11 12 13
14 15 16 17 18 19 20
21 22 23 24 25 26 27
28 29 30 31
Forum Donations
The TnDeer.Com Deer Talk Forum is for Tennessee Deer Hunters by Tennessee Deer Hunters. If you enjoy using our Talk Forum and would like to contribute to help in it's up-keep. Just submit your contribution by clicking on the DONATE button below and paying with PayPal or a major credit card. Any amount is much appreciated. Thanks for your support!

TN Burn Safe

Generated in 0.006 seconds in which 0.001 seconds were spent on a total of 14 queries. Zlib compression enabled.