Tndeer Logo

Page 2 of 2 <12
Topic Options
#3184089 - 03/05/13 10:43 AM Re: turning case necks? [Re: mr.big]
EastTNHunter
10 Point


Registered: 03/08/10
Posts: 2629
Loc: Rhea Co., TN

Offline
 Originally Posted By: mr.big
may need to set your size die a little shorter also,,


^^^^^^^^^^

Top
#3184259 - 03/05/13 01:57 PM Re: turning case necks? [Re: DaveB]
Hunter 257W
10 Point


Registered: 10/04/12
Posts: 2579
Loc: Franklin County

Offline
Just to clarify something here that I think is misunderstood. Turning Case necks means to remove metal from the outside diameter of the entire length of the case neck much as a metal turning lathe does. That is different from Trimming case necks which simply shortens a case by cutting the face of the neck. Usually nobody turns necks except for benchrest rifles or very accurate varmint rifles. On the other hand, trimming necks is common because all cases tend to grow in length each time they are loaded and will eventually jam into the front of the chamber. The case mouth is then forced to swage into the bullet which causes chamber pressure to rise which is not a good thing. \:\)

It's always a good idea to check case length against a Manual every time you reload a batch of cases. Then if a few are starting to reach or exceed the Max, trim the whole batch back to the Min length.


Top
#3184274 - 03/05/13 02:08 PM Re: turning case necks? [Re: Hunter 257W]
Hunter 257W
10 Point


Registered: 10/04/12
Posts: 2579
Loc: Franklin County

Offline
Mr. Big may have the answer. When setting up a sizing die you have a little latitude to vary die depth in the press and still produce safe ammo. It's acceptable to just let the bottom of the die "kiss" the shell holder or turn the die down another 1/8 turn or so. You may have a shorter than average chamber that would benefit from turning the sizing die into the press maybe 1/8 turn beyond 1st contact with the shell holder. If it were mine, I'd go half that distance and see how it feels. You don't want to go too far and create an excessive headspace problem. That will lead to case head separations which is not fun!
Top
Page 2 of 2 <12


Moderator:  RUGER, gtk, Bobby G, Unicam, CBU93, stretch, TurkeyBurd, Kimber45, Kirk, Crappie Luck 
Hop to:
Top Posters
4104337
RUGER
85523
Deer Assassin
64216
BSK
59468
Crappie Luck
51368
spitndrum
Newest Members
fghijk604245, top_of_the_foodchain, infantryleadtheway, ftwstn, Wild hog 44
13286 Registered Users
Who's Online
6 registered (in the dog house!, UTGrad, backwoods7, HuntNFish321, Doc Stone, jaybird62) and 93 anonymous users online.
Forum Stats
13286 Members
42 Forums
85284 Topics
1030791 Posts

Max Online: 788 @ 11/11/13 08:06 PM
Moon Phase
CURRENT MOON
April
Su M Tu W Th F Sa
1 2 3 4 5
6 7 8 9 10 11 12
13 14 15 16 17 18 19
20 21 22 23 24 25 26
27 28 29 30
Forum Donations
The TnDeer.Com Deer Talk Forum is for Tennessee Deer Hunters by Tennessee Deer Hunters. If you enjoy using our Talk Forum and would like to contribute to help in it's up-keep. Just submit your contribution by clicking on the DONATE button below and paying with PayPal or a major credit card. Any amount is much appreciated. Thanks for your support!

TN Burn Safe

Generated in 0.221 seconds in which 0.001 seconds were spent on a total of 15 queries. Zlib compression enabled.