Tndeer Logo

Page 1 of 2 12>
Topic Options
#3181199 - 03/02/13 12:57 PM turning case necks?
deerkiller300wsm
6 Point


Registered: 10/22/08
Posts: 568
Loc: maryville,tn

Offline
Who does it? I think I am going to have to start turning case necks on my 300 Wsm. I have tried different bullets at diff oal and most are sticky in the chamber. I prep my case throughly too! I chamfer and debur trim.....never had to trim case necks though. Any suggestions?
Top
#3181243 - 03/02/13 02:24 PM Re: turning case necks? [Re: deerkiller300wsm]
Jcalder
8 Point


Registered: 09/18/12
Posts: 1201
Loc: Tennesse

Offline
What exactly is sticky and when is it sticky?
Top
#3181517 - 03/02/13 06:40 PM Re: turning case necks? [Re: Jcalder]
deerkiller300wsm
6 Point


Registered: 10/22/08
Posts: 568
Loc: maryville,tn

Offline
It is just more difficult to close the bolt than what I am used to with factory ammo.
Top
#3181586 - 03/02/13 07:33 PM Re: turning case necks? [Re: deerkiller300wsm]
JRE
4 Point


Registered: 11/04/05
Posts: 182
Loc: Knoxville, TN

Offline
Sounds like if its hard to close the bolt you may be jambing the bullets into the lands. If its hard to lift the bolt after firing there could be too much pressure (i.e. hot load).
Top
#3181592 - 03/02/13 07:40 PM Re: turning case necks? [Re: JRE]
Jcalder
8 Point


Registered: 09/18/12
Posts: 1201
Loc: Tennesse

Offline
What JRE said. You may need to seat them a bit farther.
Top
#3181608 - 03/02/13 07:54 PM Re: turning case necks? [Re: Jcalder]
mr.big
Non-Typical


Registered: 01/03/01
Posts: 28834
Loc: Copper Head Road

Offline
may need to set your size die a little shorter also,,
_________________________
gun junky

Top
#3181641 - 03/02/13 08:38 PM Re: turning case necks? [Re: mr.big]
KPH
10 Point


Registered: 08/06/05
Posts: 3869
Loc: Hendersonville Tenn

Offline
All the above, plus make sure you cases are the right length, they do sometime grow. I have to trim my 22-250 cases some, after being shot.
_________________________
I can spell I just can't type.

Top
#3181764 - 03/02/13 10:44 PM Re: turning case necks? [Re: KPH]
skynimrod
10 Point


Registered: 11/10/06
Posts: 2543
Loc: Bellevue Tn

Offline
Back off the shoulder a touch, or try neck sizing your all ready fired brass.
_________________________
Manipulation is the KEY!
Use it willfully & be aware of it from others!

Top
#3182128 - 03/03/13 01:03 PM Re: turning case necks? [Re: skynimrod]
deerkiller300wsm
6 Point


Registered: 10/22/08
Posts: 568
Loc: maryville,tn

Offline
I don't think I am on the lands......I am well below oal.
Top
#3184037 - 03/05/13 10:05 AM Re: turning case necks? [Re: deerkiller300wsm]
DaveB
10 Point


Registered: 09/03/08
Posts: 4332
Loc: Shelby County

Offline
You are below OAL and you have to crank the bolt closed? The suggestion is your sizing die is not set correctly, that is what earlier posts are saying. You have measured you brass oal and it is within the SAMMI specs, right? If so, then on to next step.

Drop am empty case you are ready to reload into the chamber and close the bolt. Crank over hard, same as before? Die set wrong. Remove the die, reinstall according to instructions, and size the case that wouldn't fit easily. re-try the empty case for fit. Still doesn't work? If you have one, take a once-fired factory round and without sizing, try the test.

Every time you change the FL die you should be following some sort of test to insure the die is set correctly.

Top
Page 1 of 2 12>


Moderator:  RUGER, gtk, Bobby G, Unicam, CBU93, stretch, TurkeyBurd, Kimber45, Mrs.Unicam, Crappie Luck 
Hop to:
Top Posters
4105885
RUGER
87625
Deer Assassin
65683
BSK
61403
Crappie Luck
51376
spitndrum
Newest Members
TnDear, buckslayer85, crose84, Fisher 1959, AKeys
13384 Registered Users
Who's Online
106 registered (Buckbuster03, larry.boy.k, pastorbmp, ADR, Southpaw, pse2, 3 invisible) and 195 anonymous users online.
Forum Stats
13384 Members
42 Forums
96030 Topics
1124480 Posts

Max Online: 788 @ 11/11/13 08:06 PM
Moon Phase
CURRENT MOON
October
Su M Tu W Th F Sa
1 2 3 4
5 6 7 8 9 10 11
12 13 14 15 16 17 18
19 20 21 22 23 24 25
26 27 28 29 30 31
Forum Donations
The TnDeer.Com Deer Talk Forum is for Tennessee Deer Hunters by Tennessee Deer Hunters. If you enjoy using our Talk Forum and would like to contribute to help in it's up-keep. Just submit your contribution by clicking on the DONATE button below and paying with PayPal or a major credit card. Any amount is much appreciated. Thanks for your support!

TN Burn Safe

Generated in 0.073 seconds in which 0.001 seconds were spent on a total of 15 queries. Zlib compression enabled.