#3181199 - 03/02/13 12:57 PM
turning case necks?
|
deerkiller300wsm
4 Point
Registered: 10/22/08
Posts: 438
Loc: maryville,tn
|
Offline
|
|
Who does it? I think I am going to have to start turning case necks on my 300 Wsm. I have tried different bullets at diff oal and most are sticky in the chamber. I prep my case throughly too! I chamfer and debur trim.....never had to trim case necks though. Any suggestions?
|
|
Top
|
|
|
|
|
#3181243 - 03/02/13 02:24 PM
Re: turning case necks?
[Re: deerkiller300wsm]
|
Jcalder
4 Point
Registered: 09/18/12
Posts: 227
Loc: Tennesse
|
|
Offline
|
|
What exactly is sticky and when is it sticky?
|
|
Top
|
|
|
|
|
#3181517 - 03/02/13 06:40 PM
Re: turning case necks?
[Re: Jcalder]
|
deerkiller300wsm
4 Point
Registered: 10/22/08
Posts: 438
Loc: maryville,tn
|
|
Offline
|
|
It is just more difficult to close the bolt than what I am used to with factory ammo.
|
|
Top
|
|
|
|
|
#3181586 - 03/02/13 07:33 PM
Re: turning case necks?
[Re: deerkiller300wsm]
|
JRE
4 Point
Registered: 11/04/05
Posts: 153
Loc: Knoxville, TN
|
|
Offline
|
|
Sounds like if its hard to close the bolt you may be jambing the bullets into the lands. If its hard to lift the bolt after firing there could be too much pressure (i.e. hot load).
|
|
Top
|
|
|
|
|
#3181592 - 03/02/13 07:40 PM
Re: turning case necks?
[Re: JRE]
|
Jcalder
4 Point
Registered: 09/18/12
Posts: 227
Loc: Tennesse
|
|
Offline
|
|
What JRE said. You may need to seat them a bit farther.
|
|
Top
|
|
|
|
|
#3181608 - 03/02/13 07:54 PM
Re: turning case necks?
[Re: Jcalder]
|
mr.big
Non-Typical
Registered: 01/03/01
Posts: 27961
Loc: Copper Head Road
|
|
Offline
|
|
may need to set your size die a little shorter also,,
_________________________
Tndeer`s resident poacher and desperate loser
|
|
Top
|
|
|
|
|
#3181641 - 03/02/13 08:38 PM
Re: turning case necks?
[Re: mr.big]
|
KPH
8 Point
Registered: 08/06/05
Posts: 1770
Loc: Hendersonville Tenn
|
|
Offline
|
|
All the above, plus make sure you cases are the right length, they do sometime grow. I have to trim my 22-250 cases some, after being shot.
|
|
Top
|
|
|
|
|
#3181764 - 03/02/13 10:44 PM
Re: turning case necks?
[Re: KPH]
|
skynimrod
10 Point
Registered: 11/10/06
Posts: 2543
Loc: Bellevue Tn
|
|
Offline
|
|
Back off the shoulder a touch, or try neck sizing your all ready fired brass.
_________________________
Manipulation is the KEY!
Use it willfully & be aware of it from others!
|
|
Top
|
|
|
|
|
#3182128 - 03/03/13 01:03 PM
Re: turning case necks?
[Re: skynimrod]
|
deerkiller300wsm
4 Point
Registered: 10/22/08
Posts: 438
Loc: maryville,tn
|
|
Offline
|
|
I don't think I am on the lands......I am well below oal.
|
|
Top
|
|
|
|
|
#3184037 - 03/05/13 10:05 AM
Re: turning case necks?
[Re: deerkiller300wsm]
|
DaveB
8 Point
Registered: 09/03/08
Posts: 1862
Loc: Shelby County
|
|
Offline
|
|
You are below OAL and you have to crank the bolt closed? The suggestion is your sizing die is not set correctly, that is what earlier posts are saying. You have measured you brass oal and it is within the SAMMI specs, right? If so, then on to next step.
Drop am empty case you are ready to reload into the chamber and close the bolt. Crank over hard, same as before? Die set wrong. Remove the die, reinstall according to instructions, and size the case that wouldn't fit easily. re-try the empty case for fit. Still doesn't work? If you have one, take a once-fired factory round and without sizing, try the test.
Every time you change the FL die you should be following some sort of test to insure the die is set correctly.
|
|
Top
|
|
|
|
Moderator: RUGER, gtk, Bobby G, Unicam, CBU93, stretch, TurkeyBurd
|
12169 Members
39 Forums
117733 Topics
1429308 Posts
Max Online: 756 @ 11/20/12 09:10 AM
|
|
|
The TnDeer.Com Deer Talk Forum is for Tennessee Deer Hunters by Tennessee Deer Hunters. If you enjoy using our Talk Forum and would like to contribute to help in it's up-keep. Just submit your contribution by clicking on the DONATE button below and paying with PayPal or a major credit card. Any amount is much appreciated. Thanks for your support!
|
|
|
