Tndeer Logo

Page 1 of 2 12>
Topic Options
#3029451 - 11/12/12 12:39 PM model seven bolt hard to close
JA1234
10 Point


Registered: 01/13/06
Posts: 3841
Loc: just a hair or two north of th...

Offline
But only sometimes. I've tried three different types of ammo but every once in a while my .260 bolt is a little hard to cycle closed and I have noticed brass shaving on the bolt face. Cold it be an issue with the bolt or just a thick case every now and again. It happens cold or hot
Top
#3029509 - 11/12/12 01:05 PM Re: model seven bolt hard to close [Re: JA1234]
W C
10 Point


Registered: 02/02/02
Posts: 2531
Loc: Alabama

Offline
Have you very thoroughly cleaned the chamber and the bolt face? It could also be crud build up in the recesses where the bolt lugs rotate into closed position but I'd bet on dirty chamber

Edited by W C (11/12/12 01:07 PM)
_________________________
Obama gets to have it both ways. He claims black from his father and American from his mother. Claiming to be a white Kenyan wouldn't get him very far though would it?

Top
#3030190 - 11/12/12 07:02 PM Re: model seven bolt hard to close [Re: W C]
JA1234
10 Point


Registered: 01/13/06
Posts: 3841
Loc: just a hair or two north of th...

Offline
Yeah I think I did. I will pull the bolt and check the chamber. I know the bolt face is clean. Being that its so erratic ,like every tenth shot, really has me confused.
Top
#3030634 - 11/13/12 06:30 AM Re: model seven bolt hard to close [Re: JA1234]
BigD_625
10 Point


Registered: 09/30/09
Posts: 3365
Loc: Maury County, TN

Offline
Buddy had a Remington 700 Boone & Crockett that would not eject ever so often. There were deep gouges on the casings. It turned out to be a very tiny burr in the chamber. Are you noticing any kind of brass shavings or scratches on the brass casing? Could be some kind of buildup.
_________________________
-----------
It's better to be smarter than you look...than to look smarter than you are.

Top
#3030646 - 11/13/12 06:36 AM Re: model seven bolt hard to close [Re: BigD_625]
JA1234
10 Point


Registered: 01/13/06
Posts: 3841
Loc: just a hair or two north of th...

Offline
Yes ...i get brass shavings on the bolt face. I will check if for burrs as well.

Thanks for your help


Edited by JA1234 (11/13/12 06:38 AM)

Top
#3030667 - 11/13/12 06:49 AM Re: model seven bolt hard to close [Re: JA1234]
FULLDRAWXX75
12 Point


Registered: 01/29/07
Posts: 6222
Loc: Adirondack Mtns, NY

Offline
Factory loads or handloads.......................

FDXX75
_________________________
“Two things are infinite: the universe and human stupidity; and I'm not sure about the universe.”
― Albert Einstein


Top
#3030682 - 11/13/12 06:57 AM Re: model seven bolt hard to close [Re: FULLDRAWXX75]
JA1234
10 Point


Registered: 01/13/06
Posts: 3841
Loc: just a hair or two north of th...

Offline
Factory. Its done it with hornady sst Remington accubonds and some other brand I can't think what they were off top of my head.
Top
#3031285 - 11/13/12 12:25 PM Re: model seven bolt hard to close [Re: JA1234]
JA1234
10 Point


Registered: 01/13/06
Posts: 3841
Loc: just a hair or two north of th...

Offline
Double checked cleaning and all looked good. Also didn't see any burs. Seems like its in the bolt face. I cleaned it and blasted all brass shavings off it. I cycles ten rounds through and each one has a mark on the rim of the case. And I have brass on the bolt face. Guess a trip to the gunsmith is due soon
Top
#3031395 - 11/13/12 01:48 PM Re: model seven bolt hard to close [Re: JA1234]
W C
10 Point


Registered: 02/02/02
Posts: 2531
Loc: Alabama

Offline
It could be the inside of the bolt is all gummed up. That could/would interfere with the extractor which would, in turn, cause the rim to be scored from forcing the rim under it. If you're confident enough to disassemble the bolt that would be my next move.
_________________________
Obama gets to have it both ways. He claims black from his father and American from his mother. Claiming to be a white Kenyan wouldn't get him very far though would it?

Top
#3031401 - 11/13/12 01:52 PM Re: model seven bolt hard to close [Re: W C]
JA1234
10 Point


Registered: 01/13/06
Posts: 3841
Loc: just a hair or two north of th...

Offline
Ok I will have to look into that. I think I can handle it if I can find good instructions online.
Top
Page 1 of 2 12>


Moderator:  RUGER, gtk, Bobby G, Unicam, CBU93, stretch, TurkeyBurd, Kimber45, Mrs.Unicam, Crappie Luck 
Hop to:
Top Posters
4104855
RUGER
86173
Deer Assassin
64740
BSK
60384
Crappie Luck
51368
spitndrum
Newest Members
TieCampBuckSlayer, ChuckNorris, Breesor1, Hunter111, THEdonkey0515
13083 Registered Users
Who's Online
59 registered (muddyboots, Jwr, muddyhunter, leader, Remington742, buckmaster 320, 10 invisible) and 124 anonymous users online.
Forum Stats
13083 Members
42 Forums
88200 Topics
1033176 Posts

Max Online: 788 @ 11/11/13 08:06 PM
Moon Phase
CURRENT MOON
July
Su M Tu W Th F Sa
1 2 3 4 5
6 7 8 9 10 11 12
13 14 15 16 17 18 19
20 21 22 23 24 25 26
27 28 29 30 31
Forum Donations
The TnDeer.Com Deer Talk Forum is for Tennessee Deer Hunters by Tennessee Deer Hunters. If you enjoy using our Talk Forum and would like to contribute to help in it's up-keep. Just submit your contribution by clicking on the DONATE button below and paying with PayPal or a major credit card. Any amount is much appreciated. Thanks for your support!

TN Burn Safe

Generated in 0.251 seconds in which 0.001 seconds were spent on a total of 15 queries. Zlib compression enabled.