#3003718 - 10/28/12 03:18 PM
243 win pressure spike
|
SEC
4 Point
Registered: 11/01/10
Posts: 493
Loc: TN
|
Offline
|
|
I worked up a load for my ruger 243 last year. The data came straight from hodgdon's website 95gr nosler partition,h4350. The starting load was 39gr and the max was 42gr. I settled on 40gr accuracy was great and all was well. Today I go to shoot and after the first shot the bolt would hardly come back to extract the brass shot it again same results primers were a little flattened. I have heard of strange pressure spikes with the 243 but its hard to understand why this lot of ammo would be fine last October and not now.
|
|
Top
|
|
|
|
|
#3003782 - 10/28/12 04:01 PM
Re: 243 win pressure spike
[Re: SEC]
|
mike243
14 Point
Registered: 09/06/06
Posts: 9822
Loc: east tn
|
|
Offline
|
|
Temp maybe?
_________________________
prayers sent for our friends in need every day
|
|
Top
|
|
|
|
|
#3003927 - 10/28/12 05:33 PM
Re: 243 win pressure spike
[Re: mike243]
|
ratsnakeboogy
10 Point
Registered: 08/28/08
Posts: 2886
Loc: Andersonville, TN
|
|
Offline
|
|
Pull a couple and re-weigh your charge on a freshly zeroed scale. I had a batch that ended up 3 gr over max one time due to something with the scale. I now weigh every charge 3 times.
Check overall length as well, if you are jamming into the lands, it will spike quick and high.
|
|
Top
|
|
|
|
|
#3004917 - 10/29/12 06:18 AM
Re: 243 win pressure spike
[Re: ratsnakeboogy]
|
7mminatree
4 Point
Registered: 01/12/12
Posts: 354
Loc: Unicoi Tn.
|
|
Offline
|
|
Also, you might check your case length. If they are close to 2.045 try timming them down to 2.035, resize and try, providing you didn't over charge.
|
|
Top
|
|
|
|
|
#3005700 - 10/29/12 12:28 PM
Re: 243 win pressure spike
[Re: 7mminatree]
|
DaveB
8 Point
Registered: 09/03/08
Posts: 1799
Loc: Shelby County
|
|
Offline
|
|
All the above. That load is not near max, either your COL is too long or you have a load error. Flattened primer with that load is a heads up something not right. I run 43.5 grains of RL19 in my 243, 95 grain partitions, I get flat primers but back it off two grains and its gone.
|
|
Top
|
|
|
|
|
#3006686 - 10/29/12 09:24 PM
Re: 243 win pressure spike
[Re: DaveB]
|
Mid
4 Point
Registered: 10/06/12
Posts: 166
Loc: Kingston Springs, TN
|
|
Offline
|
|
.243 is hard on brass...sharp shoulders and high pressures anyway...i reload a lot of them. if you are loading the same brass over and over in .243 they become "case hardned" pretty quick. i anneal my cases every 3rd load and after 3rd anneal i toss them. this is not "the" reason for sticky cases and pressure signs but an other thing to look at. BTW i run 105AMAX over h4350 at +2 over book but i worked up to it very slowly to the accuracy node in my rifle....nasty hunting round
_________________________
“Welcome to Tennessee, patron state of shootin' stuff." - Bob Lee Swagger "Tu ne cede malis sed contra audentior ito" ΜΟΛΩΝ ΛΑΒΕ http://www.TNPredators.com
|
|
Top
|
|
|
|
Moderator: RUGER, gtk, Bobby G, Unicam, CBU93, stretch, TurkeyBurd
|
12113 Members
38 Forums
116002 Topics
1412647 Posts
Max Online: 756 @ 11/20/12 09:10 AM
|
|
|
The TnDeer.Com Deer Talk Forum is for Tennessee Deer Hunters by Tennessee Deer Hunters. If you enjoy using our Talk Forum and would like to contribute to help in it's up-keep. Just submit your contribution by clicking on the DONATE button below and paying with PayPal or a major credit card. Any amount is much appreciated. Thanks for your support!
|
|
|
