Tndeer Logo

Page 1 of 1 1
Topic Options
#1614374 - 11/12/09 09:16 PM Tutorial On How I Make Pots And Strikers
Stoner
6 Point


Registered: 10/03/06
Posts: 680
Loc: Florida

Offline
I cannot remember if I posted this here before or not. I posted this on another call makers board and one of the forum members here was asking how I make my calls. There are many ways to make pot calls, below is just how I do it. Stoner.

I wanted to put together a tutorial to help the new fellows wanting to learn how to make friction calls. The thickness of the wood should be a minimum of 1 inch thick and should be 4 inches in width and length. Most of the time I cut it a hair bigger then the 4-inch square. Before you draw your X on the wood to find the center of each square look at the wood and determine which side has the best grain for the outside of your call.



After you have found the center of the square by drawing an X use a fortsner bit to drill a hole in the center of each block of wood. The side that I drill the hole in the wood blank is going to be the inside of the call. The size fortsner bit that I use is the same diameter as a penny. Many times I will use the same fortsner bit to inlay a penny in the bottom of my calls. For the depth of the hole I am drilling with the fortsner bit I estimate two thickness of the top surfaces (glass or slate). It does not have to be exact, but you do not want to go too deep. Once you take the wood away it will not grow back. After you have done a few you can look at the sides of your fortsner bit and be able to judge the correct depth for the hole.





The next step to round the corners off to save some time on the lathe and avoiding the risk of spliting one of your wood blanks. I have been using a chop saw to cut off the corners. I ordered a band saw so it should make this step a littler easier. If you use a band saw you can use the half of the circle and use the scrap wood as a stand for your call and a striker when you are finished. I put a picture below of the stand to give you and idea what I have been doing. I hate to waste wood.





I next take the wood blank with the corners cut off an use an expandable set of jaws on my chuck and insert the jaws in the hole we drilled with the fortsner bit.



To round the wood blank I use a large rough gouge as shown in the picture below. Take your time and keep your tools sharp. At this point you can go ahead and do most of your final shaping and sanding to the outside of the call.



After the blank has been made round I take it off the lathe and use the top surface of the call (slate, glass, or aluminum) and lay it on the call are trace the outside surface on the call.



In the picture below you will note that I change the jaws on the chuck to a flat jaw with the rubber posts. I have turned over the wood blank over so we can start carving out the inside of the call. I start with a parting tool and go to the INSIDE of the circle that was traced on the inside of the call as shown above. You do not want to start you cut on the line you traced. If you do you will have a sloppy cut and your top surface will not fit snug. Only cut deep enough so you surface will lay flush with the surface of the call.



So you do not cut too deeply with you parting tool hold it up next to the outside of your call and mark your parting tool with a pencil so you do not go too deep.





After my first cut on the inside the line that I traced for the top surface I move in with the parting tool one width of my parting tool and cut down to the depth that I marked with the pencil on my parting tool. I next determine what diameter I want for the pedestal for the soundboard and cut down the depth that I marked with the pencil on my parting tool. At this point I cut the remaining wood out between the pedestal and edge of the call. Remember to leave the lip on the edge to lay your top surface. The tools that I use to clean out the wood is the parting tool or gouge. After that wood has been cleaned out I use a sharp skew to flatten the bottom of the inside of the call. It is more cosmetic then anything. I just like neat work even though no one sees the inside of the call. I next use the skew to lower the pedestal a little bit at a time. I like to have 1/8 of an inch from the bottom of my top surface to the top of the soundboard. After I shaved off the pedestal with the skew I will periodically lay the soundboard on top of the pedestal and eyeball the distance from the top of the soundboard to the lip I cut in the side of the call for the top surface. After you have done a few you will not need to measure. The spacing is very important to get a good turkey sound.



At this point I take the call off the lathe and use aluminum template to mark my sound holes and drill them out. You should drill from the outside in with your fortsner bit to avoid having the wood tear around the edge of the holes. If you drill from the inside out the wood will tear where the drill bit comes out and you have ruined the appearance of your call.





Next I put the call back on the flat jaw chuck; in the picture below you will not see the rubber posts on the flat jaw chuck. The rubber posts have been moved in towards the center of the chuck and are not visible because they are inside the call.



I mount the call this way to do the final sanding, finishing, and polishing of the call.

Most strikers are between 7 and 8 inches long. I usually cut a board into1-inch squares and 10 to 11 inches long. I mark and X in one end to find the center and use a punch to make an indention for my tailstock on the lathe to fit into. I use a pincher chuck one the other end. I use a rough gouge to turn the block of wood into a round cylinder.





I then use a marker to mark the ends of the striker. I also mark the length of the handle for the striker and the length of any decorative carving I am going put on the handle while on the lathe.

The biggest mistake that I made when I first started turning strikers was I was making them too fat. I believe the straight portion of the striker below the handle should not be more then a thick. Where the striker comes into contact with the call. I do all the sanding and finishing on the lathe. After I do the finishing on the striker I cut it off with a parting tool on the tailstock end of the lathe first. Then go back and finish the wood where is it was cut off the lathe. After I cut off the other end of the striker I use some 60 grit sandpaper and cup it in my hand and turn the striker back and forth to round the tip a little then I use the same sand paper and sand the point from the center out to the edge of the point.

I hope this helps some of the new call makers. I received a lot of help from veteran call makers along the way. Have some fun and turn a few calls. Stoner








Top
#1614779 - 11/13/09 04:16 AM Re: Tutorial On How I Make Pots And Strikers [Re: Stoner]
strutandrut
Non-Typical


Registered: 07/03/06
Posts: 28975
Loc: signal mountain

Offline
Dude, that is cool.
_________________________
Any day above ground is a good day.

Why do I carry a gun? Because cops weigh too much to carry and are difficult to conceal.

ΜΟΛΩΝ ΛΑΒΕ

Top
#1615968 - 11/13/09 04:01 PM Re: Tutorial On How I Make Pots And Strikers [Re: strutandrut]
drrxnupe
6 Point


Registered: 02/15/09
Posts: 936
Loc: Nashville, TN & Oxford, MS

Offline
You should be on the Discovery show "How It's Made"
Top
#1616626 - 11/14/09 04:32 AM Re: Tutorial On How I Make Pots And Strikers [Re: ]
buckdead
8 Point


Registered: 11/02/08
Posts: 2274
Loc: southern middle tn

Offline
Do you sell calls Stoner? Ive bought a couple nice pot calls and a trumpet from some of the call makers on oldgobbler.com. Been thinking about getting some to hand out for christmas presents this year.
_________________________
if your gonna be stupid you gotta be tough.

Top
#1616753 - 11/14/09 09:48 AM Re: Tutorial On How I Make Pots And Strikers [Re: buckdead]
SuperX2
4 Point


Registered: 04/22/05
Posts: 412
Loc: Nashville, TN

Offline
WOW. I respect your talent and craftsmanship immensely, sir!

Thanks for posting this... GREAT stuff!

Top
#1618694 - 11/15/09 06:27 PM Re: Tutorial On How I Make Pots And Strikers [Re: buckdead]
Stoner
6 Point


Registered: 10/03/06
Posts: 680
Loc: Florida

Offline
 Originally Posted By: buckdead
Do you sell calls Stoner? Ive bought a couple nice pot calls and a trumpet from some of the call makers on oldgobbler.com. Been thinking about getting some to hand out for christmas presents this year.


I am not in business to sell calls; I make them for friends and some non-profit groups. What I do for people that want me to make a call is that I tell them to send me the wood that they want the call made out of. If a person wants a custom turkey call of a lifetime they need to be selective in the wood that they chose. A nice maple burl, curly sapele, curly koa, nice figure piece of walnut can make some very attractive calls that you will be proud to show your turkey hunting partners. If I build a call for someone I request that board be a least two-feet and 7.5 8 inches wide. The thickness of the board at a bare minimum should be 1 inch thick. Thicker is better, 1 to 1 is suggested. I would stay away from oak unless is an unusual piece of wood. I keep the rest of the wood and will make one pot and one striker. My turn-around time is about a month. I do this in my spare time and I take my time on the finish of the call. I put six layers of a hand rubbed finish on each call. Each layer takes 24 hours to cure. Also the wood need to be dry and not wet or green. I do not charge any additional fee, I include the labor, the slate and a crystal soundboard.

Top
#1626459 - 11/19/09 07:47 AM Re: Tutorial On How I Make Pots And Strikers [Re: ]
LA man
18 Point


Registered: 05/31/03
Posts: 20162
Loc: spencer, tn/houma, la.

Offline
AWESOME JOB, WITH THE RIGHT TOOLS ANYTHING CAN BE DONE
_________________________
GO LSU

Top
Page 1 of 1 1


Moderator:  RUGER, Bobby G, Unicam, Cuttin Caller, CBU93, stretch, TurkeyBurd, Kimber45, Mrs.Unicam, Crappie Luck, Grizzly Johnson 
Hop to:
Top Posters
4104881
RUGER
86295
Deer Assassin
64812
BSK
60498
Crappie Luck
51375
spitndrum
Newest Members
Deadeye14, woodie, Montana10point, sandman064, MossyOak30
13107 Registered Users
Who's Online
57 registered (bone_cave, HuntNShoot, feldmutze, leader, fairchaser, J.W.308, 8 invisible) and 88 anonymous users online.
Forum Stats
13107 Members
42 Forums
88994 Topics
1041100 Posts

Max Online: 788 @ 11/11/13 08:06 PM
Moon Phase
CURRENT MOON
July
Su M Tu W Th F Sa
1 2 3 4 5
6 7 8 9 10 11 12
13 14 15 16 17 18 19
20 21 22 23 24 25 26
27 28 29 30 31
Forum Donations
The TnDeer.Com Deer Talk Forum is for Tennessee Deer Hunters by Tennessee Deer Hunters. If you enjoy using our Talk Forum and would like to contribute to help in it's up-keep. Just submit your contribution by clicking on the DONATE button below and paying with PayPal or a major credit card. Any amount is much appreciated. Thanks for your support!

TN Burn Safe

Generated in 0.23 seconds in which 0.013 seconds were spent on a total of 14 queries. Zlib compression enabled.